Skip to content

How To Fix Start Pxe Over Ipv4 In Windows 10

July 7, 2022
How To Fix Start Pxe Over Ipv4 In Windows 10
How To Fix Start Pxe Over Ipv4 In Windows 10

Start pxe over ipv4 is an error message that usually appears when trying to start the computer through the local network. This code appears immediately after restarting or turning on the computer.

After this error, the system keeps booting with a dotted circle and it takes 2-3 minutes to boot.

This error message appears when the boot process has not been configured correctly in the BIOS. If the system cannot recognize the boot drive, try to load the data from the local networkwhich causes the error message to appear.

You can also read: How To Fix Flight Simulator X Error 1722 In Windows 10

Index of contents

  1. How to fix Start pxe over ipv4 in Windows 10
    1. Solution 1: Connect a bootable media
    2. Solution 2: Disable Wake on LAN feature in BIOS
    3. Solution 3: Update BIOS
  2. conclusion

How to fix Start pxe over ipv4 in Windows 10

Solution 1: Connect a bootable media

If you get this error, sometimes you can reset some settings to restore the correct boot order, and you may need to re-add the hard drive as the default boot device. This procedure changes some very important settings. So be careful and follow the instructions carefully.

  • Turn on the computer and immediately press the settings button several times, approximately every second, until the computer’s setup program opens. This button should appear on your computer screen as if you had pressed _ to start setup.
  • Use the right arrow key to select the Security menuuse the Down arrow key to select Configure Secure Boot, and then press the Enter key.
  • It will show you a warning before using this menu. Press the F10 key to display the secure boot configuration menu.
  • The secure boot configuration menu will appear.
  • Use the down arrow key to select Secure Boot, and then use the right arrow key to change the setting to Disable.
  • With the down arrow key, select Legacy Support and then use the right arrow key to change the setting to Enable.
  • Press the F10 key to apply the changes.
  • Select the File menu with the left arrow key, select save changes and exit with the down arrow key, and then press Enter to select Yes.
  • The computer installer will close and the computer will restart. After the computer restarts, use the power switch to turn it off.

If you don’t know how to restart your computer from the hard drive, you should know which option to select when you open the Start menu. It will ask you which device you want to boot from. Follow the instructions below to easily reboot your computer from the hard drive.

  • Press the power button to turn on the computer. When the computer starts, you will see a message indicating that the startup mode has changed.
  • Enter the four-digit code that appears in the message and press the Enter key to confirm the change.

NOTE: There is no text field to enter the code. This is the expected behavior. When numbers are entered, the code is stored without a text field.

  • Press the power key to turn off the computerwait a few seconds, turn on your computer, and immediately press the escape key repeatedly, about once every second, until the Start menu appears.
  • Press the F9 key to open the Start menu.
  • Use the down arrow key to select your hard drive from the Start menu, and then make sure it is selected by pressing the enter key. Reboot your computer and check if the issue is resolved.

Solution 2: Disable Wake on LAN feature in BIOS

Disabling this option has helped people who were unsuccessful using other methods, and this method is fairly easy if you feel confident enough to boot into the BIOS yourself, as you’ve shown by trying the method above.

  • Shut down the computer by selecting Start Menu>> Power key >> Power off.
  • Turn on the computer and open the BIOS by pressing the BIOS key after booting. The BIOS key will normally appear on the boot screen with the words “Press ___ to enter setup.” (Press ___ to enter settings). The most common BIOS keys are F1, F2, Erase, Esc and F10. Take your time, as the message disappears quickly.
  • The Wake-on-LAN option you need to change is in the BIOS software tabs of various manufacturers and there is no single way to find it. It’s usually found under “Power Options” or another item with a similar name, such as “Wake-on-LAN.”
  • If the Network Wakeup option is in any section of the BIOS setup screen, go to that section and change the value to Disabled.
  • Go to Finish and select Finish to save your changes. This will continue the boot process. Check if the error still occurs.

Solution 3: Update BIOS

If the problem is in your computer’s BIOS, it’s hard to say that anything else will solve the problem short of a full BIOS update. Updating the BIOS can be a complicated process, and the problem is that it varies a lot from one manufacturer to another. Therefore, you will have to follow the instructions carefully if you want to see results.

  • To check the current BIOS version installed on your computer, enter the command msinfo in the search bar of the Start menu.
  • Locate the BIOS version just below the CPU model and copy or annotate it in a text file or on paper.
  • Determine if the computer was packaged, pre-assembled, or hand-assembled by purchasing all components separately. This is important because you don’t want to use the BIOS of one computer component if it doesn’t fit the others, and you risk replacing the BIOS with the wrong one, which can lead to system crashes and serious problems.
  • Prepare your computer for the update. If you’re upgrading your laptop, make sure the battery is fully charged and turn it on just in case. If you are upgrading your computer, it is advisable to use a UPS (Uninterruptible Power Supply) to ensure that your computer does not fail due to a power failure during the upgrade.

conclusion

A simple boot order tweak resolves a common error Running pxe over ipv4. When the boot priority is set to LAN, this error message appears on the computer screen for an unknown reason. If you have any problem, do not hesitate, we will help you in any way we can.

You can also read: How to Fix “OpenAL32.dll is Missing” Error in Windows 10